Motor Servo for Angled Seat Valves for MATTER

SKU: KFRMAT01
Version: 1.6

• 1. Product Description
• 2. Parts of the Motor
• 3. Installation of the motor
• 3.1. Mounting the motor on the valve
• 3.2. Valves from Wilhelm Ewe GmbH and Co. KG
• 3.3. Custom Adapter
• 3.4. Setting the End Positions of the Motor Drive
• 4. External Cable Water Sensor
• 5. Operation on the Device Itself
• 5.1. Button Operation
• 5.2. LED Signals
• 6. Connection with a MATTER Control Unit
• 7. Scope of Delivery - motor
• 8. Technical Data
• 8.1. Valve Motor
• 8.2. Wireless Communication
• 9. Support and Contact
• 10. Declaration of Conformity
• 11. Disposal Guidelines

1. Product Description

The motor drive for angle seat valves (KFR valves) allows retrofitting of existing and already installed shut-off valves into radio-controlled intelligent devices without interrupting the water supply or cutting into the water pipe. The motor is powered by a 12V power supply and is completely water- and dirt-protected up to the power supply. Various adapter rings and a sophisticated connection system enable the motor's use on all modern angle seat valves from DN15 to DN32. Thanks to an additional water sensor that plugs directly into the device, the motor can be used for leakage protection without further configuration.

The servo motor is water-protected and can be used in damp, dirty, and outdoor environments. In the open state, the motor automatically performs valve maintenance once a week (closing/opening by 1/8 turn to remove dirt and lime). A wired leakage sensor can be connected directly to the device. If water is detected, the valve shuts off.

The device is controlled via the international communication standard MATTER. This means that the motor can be operated by control hubs from Apple (HomeKit), Google, Amazon, Samsung, Home Assistant, etc.

2. Parts of the Motor

Handwheel (H)	Inner Coupling (K)	Adapter (Ax)	Distance Rings (D1,D2)
Ball Bearing Seat (Ws)	Motor (M)	Main Body (G)	Bracket (N)

3. Installation of the motor

3.1. Mounting the motor on the valve

The motor drive can be used with all commercially available angle seat valves. However, due to the variety of mechanisms, certain adjustments must be made. When installing, the valve should be normally open (installers recommend opening the valve fully and then closing it slightly with approx. 2 clockwise turns).

1. First, loosen the screw in the center of the handwheel using a screwdriver. Some manufacturers do not use the typical green handwheel. The spindle may be hidden under plastic, but will always have a screw on top and a square end. Keep the screw for later use.
2. Now remove the handwheel.
3. Select one of the 4 adapters (A1...A4) for wrench sizes M17, M22, M27, or M30 that fits well onto the bottom of the valve top (hexagonal or rectangular shape). If none of the supplied adapters fits the valve, refer to the “Custom Adapter” section for further guidance.
4. Select the correct ball bearing seat (W1 ... W3) and place it on the spindle. If the spindle is larger than 8x8 mm, which is required for the largest ball bearing seat, this product cannot be used for this valve. If the spindle is smaller than the smallest ball bearing seat of 6x6 mm, the issue can be resolved similarly to the adapter case. See the instructions in the “Custom Adapter” section.
5. Now fix the ball bearing seat with the screw from step 1.
6. Depending on the size of the valve top and spindle, additional spacer rings (D1, D2) may be required on the adapter ring. If the inner coupler (K) cannot be pushed all the way into the main housing (G) without resting on the valve housing, or if the main housing does not reach the already installed adapter ring, a spacer ring (D1 or D2) must be placed between the adapter ring (Ax) and the main housing (G). This is usually the case with rising spindle valves. The spacer rings are 12 or 24 mm in size and can also be combined into a 26 mm ring. The spare handwheel can be used to test the opening and closing of the valve.
7. Now place the housing (G) onto the adapter or spacer ring.
8. Insert the inner coupler into the housing. It must reach over the ball bearings in both the open and closed positions. The housing is transparent for this purpose.
9. The retainer (N) is needed to hold the entire assembly in position if the valve is not installed upright. It is recommended to always use the bracket. The complete device is attached to the pipe using the two included cable ties. The cable ties can be removed at any time. To slide the retainer over the housing, the two tabs on the housing must be slightly pressed together. There are two small notches on the inner ring of the retainer for this purpose.
10. Finally, place the motor head onto the housing. Sometimes the inner coupler must be slightly rotated so that the gear structure of the motor meshes with the inner coupler.

3.2. Valves from Wilhelm Ewe GmbH and Co. KG

The valves from this company have a unique design. You must insert the split ring (E1+E2) into the 24 mm spacer ring (D1) instead of using one of the adapters A1 ... A4. A small additional spacer ring (DE) is placed directly under the ball bearing seat to fix the valve's grease chamber.

3.3. Custom Adapter

If no suitable adapter is available for the valve seat, a custom one must be made. To do this, select an adapter that fits over the valve seat and fill the gap with a two-component resin. This resin is included with the motor. Cut off a piece of the compound with a utility knife and knead it until a uniform color is achieved. Then fill the gaps between the adapter ring and the valve base. After the resin has hardened, the now custom-fit adapter ring can be used.

Note: The resin will adhere firmly to the valve. If this is not desired, lightly oil the valve beforehand. Then the hardened adapter ring can be removed more easily.

Similarly, a ball bearing seat can be adapted for a valve shaft with a square smaller than 6x6 mm. Ensure that the spindle is precisely centered in the ball bearing seat.

3.4. Setting the End Positions of the Motor Drive

Once the motor is mounted and powered, it must determine the correct end positions for the ‘OPEN’ and ‘CLOSE’ positions:

1. Manually turn the valve to the ‘OPEN’ position before the motor is initially installed. According to installer recommendations, the optimal ‘OPEN’ position is about 2 turns towards ‘CLOSE’ after reaching the stop in the ‘OPEN’ direction (counterclockwise).
2. Power the motor.
3. Press the button briefly once. The motor will now move briefly in both directions and determine whether it is in the ‘OPEN’ or, contrary to the recommendation in step 1, in the ‘CLOSE’ position. This information is indicated by the color of the LED on the device.
4. If the motor was initially in the ‘OPEN’ position, the first ‘CLOSE’ command (either via short button press or external control) will move it fully to the ‘CLOSE’ position and then slightly reverse. This function is intended to relieve the valve's rubber seal. If the seal has become brittle from long-term closing or aging, this may lead to valve leakage in the ‘CLOSE’ position. Therefore, this slight reverse function can be disabled.
   • If paired with an internet-enabled Aqua-Scope sensor, use the app in the “Configuration” section.
   • If paired with a non-internet-enabled device or used standalone, the function can be toggled on or off by pressing and holding the button for 6 seconds (6 * buzzer), then releasing.

Once the end positions are recognized, the motor will no longer forcefully drive against the valve's endpoints, but will instead count the required motor turns and approach the endpoints gently.

4. External Cable Water Sensor

An optional wired flood sensor can be connected to the device. There is a plug on the power cable near the motor. Remove the blue rubber plug and insert the sensor. Please push the connector in firmly to ensure a waterproof connection.

If the sensor head detects water, an acoustic signal will sound, the valve will close, and the alarm will be indicated by a flashing red LED. In addition, an alarm message will be sent via LoRa radio. Once the sensor head is free of water, you can clear the alarm by pressing the button for 2 seconds. It is also possible to clear the alarm via radio.

5. Operation on the Device Itself

The device has a single button with a built-in three-color LED. To operate the valve, you can either click the button or press and hold it for a few seconds. The motor helps count the seconds by beeping once per second. The device is designed for outdoor use and must prevent malfunctions caused by water drops on the button. Therefore, please press the button firmly (not too timidly), even for short clicks, so that the touchless button can detect your finger.

5.1. Button Operation

Using the button on the motor head (G), various commands can be sent to the motor:

• 1 short click: Motor turns to the opposite position (Open–Closed)
• Hold button for 2 seconds: An alarm is deactivated
• 2 short clicks: Status report is sent
• Hold button for 3 seconds, followed by one or three short clicks:
  • 1 click: Enable button lock
  • 3 clicks: Disable button lock
• Hold button for 4 seconds, followed by one or two short clicks: Behavior of the external sensor when no more water is detected (when water is detected, the motor closes)
  • 1 click (factory setting): The motor remains closed
  • 2 clicks: The motor opens again immediately
• Hold button for 5 seconds: If a Wi-Fi radio module is plugged in, this module will be reset to factory settings.
• 6 short clicks: Enable or disable relief of the rubber seal in the 'CLOSED' position
  • 2 * Beep + 2 * green LED flashes (factory setting): enabled
  • 3 * Beep + 3 * green LED flashes: disabled
• Hold button for 10 seconds, followed by 5 short clicks: Motor reset. This function is only necessary if the motor needs to switch from one of the three mentioned operating modes (pairing with main sensors, pairing with control sensors, LoRaWAN) to another.
  • 3 * Beep + 3 * red LED flashes: ok

5.2. LED Signals

The device has a two-color LED with the following meanings:

• Green slow flashing: Open
• Red slow flashing: Closed
• Red and Green fast flashing: Motor is moving
• Red flashing: Alarm
• Red triple flashing: Motor is blocked and cannot move the valve
• Yellow flashing: Searching for connection to the radio network

↑

6. Connection with a MATTER Control Unit

The Matter wireless connection of the Aqua-Scope retrofit motor is established through the Matter module, which is screwed between the coupling of the motor's power supply. Through this very power supply, the module communicates with the main device. Minimal operation of the Matter module is carried out via the central button on the main device; the Matter module itself only has a single LED to indicate its operating status, as shown in the picture.

The connection of the device to a MATTER control unit is based on the QR code printed on the MATTER module. The various MATTER controllers will always ask for exactly this QR code for pairing. Alternatively, the MATTER access code can also be entered.

To be connected with a MATTER control unit, the MATTER module must be in its factory default state. The motor must be connected to the module via cable. The button on the motor must then be pressed for 5 seconds (5 * Beep).

The LED on the module indicates the different operating states:

• Pairing mode (factory default): LED blinks continuously every 4 seconds.
• Pairing started: LED blinks continuously every 1 second.
• Pairing completed or failed: LED shows the switching state of the device.

↑

7. Scope of Delivery - motor

• Motor with power cable (150 cm) to waterproof coupling
• 4 * adapter rings to connect to the valve housing
• 3 different connectors for the stem
• One small Distancering and the Splitring for EWE Valve Design
• Holder plus 2 wrist bands
• Main sleeve plus internal coupler
• Two Distance rings
• External wired Flood Sensor
• External Power Supply with 150 cm cable to waterproof coupling
• Spare Hand Wheel
• Users Manual
• 57 gr Epoxy

↑

8. Technical Data

↑

8.1. Valve Motor

• Mechanical Performance:
• Rotation Speed: 15 rpm
• Travel Time (full open close): 40 s
• Mechanical Power: 10,95 W
• Gearbox: 1 to 704 ratio
• Noise: &lt 50 dB
• Vibration: &lt 10 dB
• Installation space:
• Min. Space from Wall: Pipe center min 35 mm from wall
• Min. Space vertically: 175 mm above pipe center
• Min. Space vertically for installation: 220 mm above pipe center
• Adapters: M17, M22, M27, M30
• Supported Stem height (from bottom of bonnet): 58 mm – 135 mm, raising and non-raising spindles
• Supported Stem connector: 6, 7, 8 mm square
• Supports Pipes DN15 … DN 32
• Controls and interfaces:
  • Tree Color LED (red, yellow, green)
  • Single button for local operation and alarm clearing
  • Jack to plug-in external water sensor pad for local loop operation
• Dimensions and Shipment:
  • Weight: 380 ... 420 gr (depends on adapters used)
  • Dimensions: 70 x (170 … 195) mm
• Electrical data:
  • Voltage: 12 V DC
  • Typ. Power Consumption when motor is moving: ca. 400 mA
  • Typ. Power Consumption in Standby: ca. 50 mA
• Environmental Conditions and Trading
• Shipment/Storage: -30 °C … +70 °C
• Operation: - 20 °C … 60 °C
• Outdoor Use: IP67 (to power supply coupling), Power Supply is IP20
• UN Customs Tariff: 85011093900

↑

8.2. Wireless Communication

• WLAN IEEE 802.11b/g/n (2.4 GHz Wi-Fi)
  • Matter Protocol

↑

9. Support and Contact

Should you encounter any problem, please give us the opportunity to address it before returning this product. Please check our website www.aqua-scope.com and particularly the support section for answers and help. You can also send a message to info@aqua-scope.com.

While the information in this manual has been compiled with great care, it may not be deemed an assurance of product characteristics. Aqua-Scope shall be liable only to the degree specified in the terms of sale and delivery. The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from Aqua-Scope. We reserve the right to make any alterations that arise as the result of technical development.

• Phone: +372 (0) 6248002
• eMail: info@aqua-scope.com
• Web: www.aqua-scope.com

↑

10. Declaration of Conformity

Aqua-Scope Technology OÜ, Sakala 7-2, 10141 Tallinn, Republic of Estonia, declares that this radio emitting device works on the following frequences:

Български С настоящото Aqua-Scope Technology OÜ декларира, че този тип радиосъоръжение KFRMAT01 е в съответств ие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери н а следния интернет адрес: www.aqua-scope.com/ce.

Čeština Tímto Aqua-Scope Technology OÜ prohlašuje, že typ rádiového zařízení KFRMAT01 je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: www.aqua-scope.com/ce.

Dansk Hermed erklærer Aqua-Scope Technology OÜ, at radioudstyrstypen KFRMAT01 er i overensstemmelse med direktiv 2014/53/EU. EUoverensstemmelseserklæringens fulde tekst kan findes p følgende internetadresse: www.aqua-scope.com/ce.

Deutsch Hiermit erklärt Aqua-Scope Technology OÜ, dass der Funkanlagentyp KFRMAT01 der Richtlinie 2014/53/EU entspricht. Der vollständige Text der EU-Konformitätserklärung ist unter der folgenden Internetadresse verfügbar: www.aqua-scope.com/ce.

Eesti Käesolevaga deklareerib Aqua-Scope Technology OÜ, et kesolev raadioseadme tp KFRMAT01 vastab direktiivi 2014/53/EL nuetele. ELi vastavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil: www.aqua-scope.com/ce

English Hereby, Aqua-Scope Technology OÜ declares that the radio equipment type KFRMAT01 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.aqua-scope.com/ce

Español Por la presente, Aqua-Scope Technology OÜ declara que el tipo de equipo radioeléctrico KFRMAT01 es conforme con la Directiva 2014/53/UE. El texto completo de la declaracin UE de conformidad está disponible en la direccin Internet siguiente: www.aqua-scope.com/ce

Ελληνικά Με την παρούσα ο/η Aqua-Scope Technology OÜ, δηλώνει ότι ο ραδιοεξοπλισμός KFRMAT01 πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρ φωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: www.aqua-scope.com/ce

Français Le soussigné, Aqua-Scope Technology OÜ, déclare que l'équipement radioélectrique du type KFRMAT01 est conforme la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible l'adresse internet suivante: www.aqua-scope.com/ce

Hrvatski Aqua-Scope Technology OÜ ovime izjavljuje da je radijska oprema tipa KFRMAT01 u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: www.aqua-scope.com/ce

Italiano Il fabbricante, Aqua-Scope Technology OÜ, dichiara che il tipo di apparecchiatura radio KFRMAT01 conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet: www.aqua-scope.com/ce

Latviešu Ar šo Aqua-Scope Technology OÜ deklarē, ka radioiekārta KFRMAT01 atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta v ietnē: www.aqua-scope.com/ce Lietuvių Aš, Aqua-Scope Technology OÜ, patvirtinu, kad radijo įrenginių tipas KFRMAT01 atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo internet adresu: www.aqua-scope.com/ce

Magyar Aqua-Scope Technology OÜ igazolja, hogy a KFRMAT01 típus rádiberendezés megfelel a 2014/53/EU irányelvnek. Az EUmegfelelőségi nyilatkozat teljes szövege elérhető a következő internetes címen: www.aqua-scope.com/ce

Malti B'dan, Aqua-Scope Technology OÜ, niddikjara li dan it-tip ta' tagħmir tar-radju KFRMAT01 huwa konformi madDirettiva 2014/53/UE. It-test kollu tad-dikjarazzjoni ta' konformit tal-UE huwa disponibbli f'dan l-indirizz talInternet li ġej: www.aqua-scope.com/ce

Nederlands Hierbij verklaar ik, Aqua-Scope Technology OÜ, dat het type radioapparatuur KFRMAT01 conform is met Richtlijn 2014/53/EU. De volledige tekst van de EUconformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: www.aqua-scope.com/ce

Polski Aqua-Scope Technology OÜ niniejszym oświadcza, że typ urządzenia radiowego KFRMAT01 jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodnośc I UE jest dostępny pod następującym adre sem internetowym: www.aqua-scope.com/ce

Português O(a) abaixo assinado(a) Aqua-Scope Technology OÜ declara que o presente tipo de equipamento de rádio KFRMAT01 está em conformidade com a Diretiva 2014/53/UE. O texto integral da declarao de conformidade está disponível no seguinte endereo de Internet: www.aqua-scope.com/ce

Română Prin prezenta Aqua-Scope Technology OÜ declară că tipul de echipamente KFRMAT01 este în conformitate cu Directiva 2014/53/UE. Textul integral al declarației UE de conformitate este disponibil la următoarea adresă internet: www.aqua-scope.com/ce

Slovensko Aqua-Scope Technology OÜ potrjuje, da je tip radijske opreme KFRMAT01 skladen z irektivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: www.aqua-scope.com/ce

Slovensky Aqua-Scope Technology OÜ týmto vyhlasuje, že rádiové zariadenie typu KFRMAT01 je v slade so smernicou 2014/53/EÚ. Úplné EÚ vyhlásenie o zhode je k dispozícii na tejto internetovej adrese: www.aqua-scope.com/ce

Soumi Aqua-Scope Technology OÜ vakuuttaa, että radiolaitetyyppi KFRMAT01 on direktiivin 2014/53/EU mukainen. EUvaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: www.aqua-scope.com/ce

Svenska Härmed försäkrar Aqua-Scope Technology OÜ att denna typ av radioutrustning KFRMAT01 verensstmmer med direktiv 2014/53/EU. Den fullständiga texten till EUförsäkran om verensstämmelse finns på följande webbadress: www.aqua-scope.com/ce

↑

11. Disposal Guidelines

Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging health and well-being.